ABS Pipe 3M Length 25mm
Part number: ABSG008-25
ABS Pipe 3M Length 25mm - Grey
Please call or Enquire Here for pricing

qty

ABS Socket Union 25mm
Part number: ABSG003-25
Used for breaking a section of aspirating smoke detection pipe network for maintenance purposes.

Please call or Enquire Here for pricing

qty

ABS Sharp 90 Degree Bend
Part number: PIPG-017
Designed for changing the direction of a pipe run at 90 degree’s on an aspirating smoke detection pipe network.
Please call or Enquire Here for pricing

qty

ABS Tee 25mm
Part number: ABSG006-25
This device is used when a “Bull nose” or “Side tee” flow split is required.

Please call or Enquire Here for pricing

qty

ABS Clips 25/27mm
Part number: ABSG004
Aspirating smoke detection pipe clip, Designed to support both 25mm and 27mm aspirating detection smoke pipe.
Please call or Enquire Here for pricing

qty

ABS Tee Adaptor 25/10mm
Part number: PIPG-016
Used to connect the aspirating pipe to 10mm OD flexible nylon tubing.
Please call or Enquire Here for pricing

qty

ABS Conical Sampling Kit
Part number: ABSG019C
Used when sampling is required in a chill or cold store. The conical head prevents ice or condensation from covering the sampling hole.

Please call or Enquire Here for pricing

qty

ABS Discrete Kit
Part number: ABSG020
The capillary Tee piece fits on to the pipe run. Is followed by a 2meter 10mm OD nylon tube which links into the discrete head.

Please call or Enquire Here for pricing

qty

ABS Flush End Cap Kit
Part number: ABSG019F/25EC
The capillary end cap fits on to the end of the pipe run. There is then a 2 meter 10mm OD nylon tube which links in to the flush sampling head, which is fixed by a nylon nut/washer to the ceiling tile.

Please call or Enquire Here for pricing

qty

ABS Flush Head Only
Part number: PIP-015
Used to fix to a ceiling tile with the nut or washer (supplied) to sample air.



Please call or Enquire Here for pricing

qty

ABS Conical Head Only
Part number: E700-SP
Is fixed to a ceiling tile, chill or frozen store ceiling with the nut or washer (supplied) to sample air. The conical shape is specifically designed to avoid ice or condensation from freezing over or covering the sampling hole.

Please call or Enquire Here for pricing

qty

Discrete Head Only
Part number: W222-059
A non-intrusive sampling point.

Please call or Enquire Here for pricing

qty

Air Sampling Point Label
Part number: ABS128-014
Air Sampling Point Label 128-014 - Pack of 100pcs.
Please call or Enquire Here for pricing

qty

Sampling Point Wrap Round Label
Part number: ABS128-046
Sampling Point Wrap Round Label - Pack of 200pcs.
Please call or Enquire Here for pricing

qty

Refrigerated Storage Sampling Kit
Part number: VSP-860
Refrigerated Storage Sampling Kit provides a standardised method of smoke sampling for Refrigerated Storage facilities in a considerably improved manner allowing simplified installation with reduced maintenance, thus promoting more reliable and hassle-free operation.
Refrigerated Storage Sampling Kit has been designed to replace standard cone-shaped sampling nozzles installed at the ceiling in existing or new Refrigerated Storage facilities.
This kit can be installed in the entire facility or combined with standard sampling points if required. The aim here is to reduce direct ice blockage of the sampling points hence this kit is recommended for installation in areas where higher humidity is likely to occur as a result of vehicle and pedestrian traffic (e.g. areas close to doorways or perimeter of the facility).
Please call or Enquire Here for pricing

qty

Flexi Bend 30cm
Part number: PIPG-026
Soft PVC hose with embedded steel wire reinforcement. Very flexible, strong, abrasion resistant, smooth inside and outside.
Please call or Enquire Here for pricing

qty